Suche
Erweiterte Suche
Mein Warenkorb 0
  • Home
  • Thermaltake Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression – Black
Thermaltake Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression – Black
Thermaltake Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression – Black

Thermaltake Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression – Black

Nicht auf Lager
P/N
CL-W092-CA00BL-A
7,99 € (included VAT)

Thermaltake Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression – Black
The Thermaltake Pacific PETG Fittings provides a complete solution for enthusiast and custom PC builders to meet the needs of setting up a complete water cooling system. With G1/4” durable copper fittings, finished in black coatings, take every detail seriously. Make your system a showcase for all to see with high quality components from Thermaltake.
 
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
 
 
High-Flow and Leak-Free Design
Made in Taiwan, the fittings allow proper connection to G1/4 ports, securing properly to cooling components while providing an even seal around the tubing. The fittings are available in chrome and black finishes, include three preinstalled O-ring. Use PETG tube for all your water cooling needs.

For tubes:
- Outer diameter: 5/8” (16 mm)
 
Remarkable Expansion
Thermaltake offers a full line of Pacific Series components for enthusiasts to build up aesthetically-superior water cooling systems by incorporating externally-modular upgrades for their chassis.


Caution
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
  1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup
  1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  4. Fill the reservoir to the top as it will prevent air from going into the pump
  5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  6. Place some paper towels under fittings and joining points to test for leaks.
  7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup:

  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
  • DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
  • Fill the reservoir to the top to prevent air from entering the pump.
  • If necessary, tilt the system slightly from side to side to bleed air out of the loop.
  • Place some paper towels under fittings and joining points to check for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
  • Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
  • Note that coolant might fade over time.
Mehr Informationen
P/N CL-W092-CA00BL-A
MATERIAL CU
Dimensions ∮25 x 18.6 (H) (mm)
Gewicht 22 g
Notiz Connector To PETG Tube
Applicable OD : 16 mm (5/8”)
Screw Thread G 1/4