Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit
Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit

Thermaltake Pacific C240 DDC Hard Tube Water Cooling Kit

Auf Lager
P/N
CL-W242-CU12SW-A
450,90 € (included VAT)

LCS Combo-Kit mit Pumpe/Reservoir, T1000-Kühlmittel, Fittings, Kupferradiator, harten Tubes und 5V Motherboard-Software steuerbaren 120mm Lüftern und W4 ARGB-Water Block und anderem Zubehör.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
Mehr Informationen
P/N CL-W242-CU12SW-A
Dimensions 520 (L) x 200 (W) x 232 (H)
Compatibility Intel LGA 2066/2011/1700/1366/1156/1155/1151/1150/775
AMD AM5/AM4/FM2/FM1/AM3+/AM3/AM2+/AM2
(CPU Socket)
Components Dimensions Pump & Reservoir: 86.54 (L) x 62 (W) x 140.1 (H) mm
Copper Radiator : 29.5 (H) x 119 (W) x 279 (L) mm
Tube Dimensions OD : 16mm , ID : 12mm
Fan Specs PWM 500~1500 RPM ,
( ARGB Controller or 5V MB ARGB Sync )
Coolant T1000 Coolant Pure Clear
Kit Contents CPU Water Block
- Pacific W4 ARGB CPU Water Block x1

Pump/Reservoir
- Pacific PR15-DDC Pump/Reservoir Combo x1

Copper Radiator
- Pacific C240 Radiator 29.5 (H) x 119 (W) x 279 (L) mm x1

ARGB Fan
- Pure 12 ARGB Sync Radiator Fan TT Premium Edition x2
- ARGB LED Controller

Fittings
- Pacific C-Pro G14 PETG 16mm OD Compression - Black x6
- Pacific G1/4 90 Degree Adapter - Black x2

Coolant
- Thermaltake T1000 Coolant Pure Clear x1

Tube
- V-Tubler PETG Tube 16mm OD 500mm x 8

Accessory
- Intel and AMD Universal Backplated & Mounting Kit
- 24pin ATX Bridge Tool x1
- Thermaltake Thermal Grease x1
- Silicone insert x1