Thermaltake P1000 Pastel Coolant – Ultimate Grey​ Thermaltake P1000 Pastel Coolant – Ultimate Grey​ Thermaltake P1000 Pastel Coolant – Ultimate Grey​ Thermaltake P1000 Pastel Coolant – Ultimate Grey​
Thermaltake P1000 Pastel Coolant – Ultimate Grey​

Thermaltake P1000 Pastel Coolant – Ultimate Grey​

Auf Lager
P/N
CL-W246-OS00GM-A
34,90 € (included VAT)
1000ml Ultimate Grey pastellfarbenes, nicht-transparentes und hochleistungsfähiges Kühlmittel für PC-Wasserkühlungen, das einen hervorragenden Schutz für Kupfer, Nickel, Messing und Aluminium bietet.
 
Bessere Formel, für ein besseres System

Korrosionsschutzlösung

Schützt Kupfer, Messing, Nickel und Aluminium.

Frostschutzmittel

Sorgt dafür, dass das Kühlmittel auch bei extremen Witterungsbedingungen effektiv läuft.

Liquid Surface Tension Optimizer

Mit dem Liquid Surface Tension Optimizer benötigt der P1000 nur etwa 5 bis 10 Sekunden, wenn das System zum ersten Mal nach dem Befüllen des Kreislaufs gestartet wird.

Unterstützer für niedrige Viskosität

Durch die niedrige Viskosität kann sich das P1000 Pastel Coolant schneller durch den Kreislauf bewegen und so die Wärme effektiver ableiten.
 
 
 

Kühlmittel Viskosität bei 20°C(m Pa‧s)

  • P1000 Pastel Coolant> 1.42m Pa‧s
  • Other Coolant> 1.93m Pa‧s

Kühlmittel Viskosität bei 40°C(m Pa‧s)

  • P1000 Pastel Coolant> 0.89m Pa‧s
  • Other Coolant> 1.2m Pa‧s
 
 
 

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup:

  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
  • DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
  • Fill the reservoir to the top to prevent air from entering the pump.
  • If necessary, tilt the system slightly from side to side to bleed air out of the loop.
  • Place some paper towels under fittings and joining points to check for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
  • Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
  • Note that coolant might fade over time.
Mehr Informationen
P/N CL-W246-OS00GM-A
Capacity 1000 ml
FARBE Ultimate Grey
Hazardous component 1,2-Propanediol (CAS 57-55-6/EC 200-338-0) < 6%