Pacific PR32-D5 (discontinued)
Thermaltake
Pacific PR32-D5
360° Drehbare Kappe
Die 360-Grad-Drehkappe ermöglicht es dem Benutzer, die Positionen der G 1/4-Gewindeanschlüsse auch nach der Montage am Gehäuse zu verstellen und bietet so mehr Flexibilität bei der Gestaltung vom Wasserkühlsystems.
Großartige visuelle Ästhetik
Das 267 mm hohe Reservoir hat ein Fassungsvermögen von 400 ml, das einen maximalen Druck von 50 PSI aushalten kann. Als Thermaltake's größter Behälter in der Kollektion, erzeugt er in der Tat einen hervorragenden optischen Effekt.
Leistungsstarke Pumpe
Der leistungsstarke Pumpenkopf kann das Kühlmittel bei maximaler Geschwindigkeit bis zu 15 Fuß hoch pumpen und bietet eine Durchflussrate von 1135 Litern pro Stunde. Mit der 5-stufigen Geschwindigkeitsregelung kann der Benutzer die Pumpendrehzahl manuell steuern und die Geschwindigkeit der Pumpe je nach Belastung des Computers anpassen.
Mehrere Installationsoptionen
Neben dem Standardbehälter und dem Pumpenständer enthält das Paket auch eine Halterung, mit der die Pacific PR32-D5 auf einem Lüfter installiert werden kann, so dass der Benutzer auch bei geringem Platzangebot in den Genuss der Wasserkühlung kommen kann.
Cautions
Thermaltake recommends the following steps to be taken
before using
the
Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop
setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
P/N | CL-W337-PL00GM-A |
---|---|
Dimensions ( mm ) | 74.8 (L) x 74.8 (W) x 274 (H) |
MATERIAL | AL + POM + PMMA |
Capacity | 400 ml |
Maximum head | 15 feet (4.5m) |
Maximum Flow Rate | 1135 L/h |
Maximum pressure | 50 PSI |
Input Voltage | 12 V |
Power Input | 37 W |
Connector | 4 Pin |
Pump Speed | P1: 1,800 RPM P2: 2,550 RPM P3: 3,300 RPM P4: 4,050 RPM P5: 4,800 RPM |
Screw Thread | G 1/4 |
Parts | 1. Stopper *1 (G 1/4 ) 2. Bracket *1 3. Clip *1 |
User Manual
- Dateiname
- Beschreibung
- Größe
- Version
- Release Date